Nts. Table 5. Conditions of laboratory experiments. Parameters SymbolUnitValueParameters Frequency of fixed
Nts. Table five. Circumstances of laboratory experiments. Parameters SymbolUnitValueParameters Frequency of fixed end of cantilever beam Frequency of fixed finish ofof cantilever beam Amplitude of fixed finish cantilever beamSymbol ffe Afeffe Rl = sUnit Hz Hz mm mm k kValue 16.3 16.3 0.2 ten, 20, 30, 40, 50, 60, 0.2 65, 70, 80AmplitudeValues of resistance of fixed finish of cantilever beam Rl =Afe s Values of resistance 4.2. Aztreonam Bacterial,Antibiotic Energy-Harvesting Process10, 20, 30, 40, 50, 60, 65, 70, 80Experiments contained existing measurements for 10 values of resistance. The course 4.2. Energy-Harvesting Approach in the measured current is presented in Figure 7a. On the basis on the values of present Experiments contained existing measurements for 10 values of resistance. The course (ig ) and resistance (Rl = s ), harvested energy (Figure 7b) was determined by the usage of the of your measured current is presented in Figure 7a. On the basis in the values of existing (ig) identified formula: and resistance (Rl = s), harvested power (Figure l7b) 2 was determined by the use of the identified Pg = R =s i g (12) formula: The measured values of power, generated by the MFC patches, (Figure 7b) had been decrease 2 than the simulated values of the energy (FigureRl = s iThe supposed result in was an interaction Pg = six). g (12) on the adhesive layers among the steel substrate along with the MFC patches. The adhesive layers limited a tension transmission among the substrate layer plus the piezoelectric material.(a)(b)Figure 7. Energy-harvesting procedure: (a) Average present generated by MFC patches; (b) Energy generated by MFC patches. Figure 7. Energy-harvesting approach: (a) Average existing generated by MFC patches; (b) Power generated by MFC patches.The measured values of power, generated by the MFC patches, (Figure 7b) have been reduce than the simulated values on the energy (Figure 6). The supposed result in was an interaction with the adhesive layers between the steel substrate as well as the MFC patches. The adhesive layers restricted a anxiety transmission between the substrate layer along with the piezoelectric material. 4.3. Vibration-Damping ProcessEnergies 2021, 14,11 of4.three. Vibration-Damping Procedure Vibrations of ten points within the beam Polmacoxib Epigenetics structure had been measured by the usage of the vision approach. An arrangement on the measured points is presented in Figure four. Motion determination of your complete beam structure was carried out in three stages. Inside the first stage, the courses of displacement of nine selected points inside the beam structure were measured 16 Energies 2021, 14, x FOR PEER Assessment 11 of for Energies 2021, 14, x FOR PEER Overview values of resistance. The displacement of exemplary point No. 10 for resistance equal to 11 of 16 ten 65 k is presented in Figure 8.Figure eight. 8. Measured displacement of point No. 10 for resistance equal to 65 k. Measured displacement of point No. 10 for resistance equal to 65 k. Figure eight. Measured displacement of point No. 10 for resistance equal to 65 k. FigureInIn the secondstage, absolute values from the displacement of nine points had been calculated the second of the displacement of nine points have been calcuIn the secondstage, absolute values of your displacement of nine points have been calcustage, absolute lated ten values of resistance. Comparison of of the absolute values in the displacements for for ten values of resistance. Comparison the absolute values with the displacements of lated for 10 values of resistance. Comparison on the absolute values on the displacements ofexemplary point No. ten for ten values of your shunt res.
